ICS 81.060.20
¥ 24
mU
GB/T 3302-2009
national standards of People’s Republic of China
Replacing GB/T 3302-1982, GB/T 11423-1989 Daily ceramic packaging, signs,
Transport and storage rules Rules of package, mark, transport and reserve
for domestic ceramic ware released on February 17, 2009
2009-07-01 Implemented by the General Administration of Quality Supervision, Inspection and Quarantine of the People’s Republic of China
Posted by Standardization Administration of China
GB/T 3302-2009
forward
Word
This standard replaces GB/T 3302-19824 Rules for Acceptance, Packaging, Marking, Transportation and Storage of Daily-Use Ceramics, and GB/T 11423-1989 “Technical Conditions for Daily-Use Ceramic Carton Packaging”.
Compared with GB/T 3302-1982 and GB/T 11423-1989, the main changes of this standard are as follows: – merged the two standards and rearranged the standard structure;
– cancel the acceptance part of daily-use ceramics; – increase the packaging design;
— Expanded the scope of packaging materials:
Modified some packaging requirements;
—Supplemented and perfected the content of the logo;
Change transportation and storage to transportation and storage, increasing the stacking height requirements. This standard was proposed by China National Light Industry Council.
This standard is under the jurisdiction of the National Ceramic Standardization Center.
This standard was drafted by: Chaozhou Entry-Exit Inspection and Quarantine Bureau of the People’s Republic of China, Fengxi Ceramic Industry Research Institute of Guangdong Province, Chaozhou Ceramic Industry Association, Guangdong Stone Group Co., Ltd., Guangdong Meidi Porcelain Industry Co., Ltd., Chaozhou Xiecheng Paper Products Co., Ltd., Chaozhou Rongchang Ceramic Craft Industry Co., Ltd.
The main drafters of this standard: Chen Pengbin, Qiu Weizhi, Huang Zhenhao, Li Shuo, Liu Maochun, Cai Zhencheng, Xie Jingcun, Zhang Yuqun, Huang Yuexi. The previous releases of the standards replaced by this standard are as follows:
-GB/T 3302-1982; –GB/T 11423-1989.
GB/T 3302-2009
Daily-use ceramics packaging, signs,
Transport and storage rules 1 Scope
This standard specifies the packaging, labeling, transportation and storage rules for daily-use ceramic products. This standard applies to the packaging, marking, transportation and storage of daily-use ceramic products.
2 Normative references
The clauses in the following documents become the clauses of this standard through the reference of this standard. For dated references, all subsequent amendments (excluding errata content) or revisions do not apply to this standard, however, encourage the parties to the agreement based on this standard to study whether the latest versions of these documents can be used . For undated references, the latest version applies to this standard.
GB/T 191 Packaging, storage and transportation icon marks
GB/T 2828.1—2003 Counting sampling inspection procedure Part 1: Batch-by-batch inspection sampling plan retrieved by acceptance quality limit (AQL) (ISO 2859-1:1999, IDT)
GB/T 2934 Universal flat pallets for intermodal main dimensions and tolerances GB/T 4122.1—2008 Packaging terms Part 1: Basics
GB/T 4857.3 Packaging – Basic tests for transport packages – Part 3: Static load stacking test method GB / T 4857.5 Packaging – Transport packages – Drop test method
GB/T 4892 Rigid cuboid transport packaging size series
GB/T 6543 transport packaging and single corrugated cartons and double corrugated cartons GB/T 9174
General technical conditions for general cargo transport packaging GB/T 12339
Protective inner packaging materials GB/T 12464
Ordinary wooden box
GB/T 15233 packaging unit cargo size GB/T 16470 pallet unit cargo
GB/T 17306 Packaging Standards Consumer Demand GB/T 18127 Coding and Symbol Marking of Logistics Units GB/T 18131 Standard Shipping Marks for International Trade GB 18455
Packaging recycling symbol GB/T 19142
General Rules for Export Commodity Packaging GB/T 19451
Shipping Package Design Procedure 3 Terms and Definitions
The terms and definitions established in GB/T 4122.1-2008 apply to this standard. 4 packs
4.1 Packaging Design
4.1.1 The packaging design should be scientific, reasonable, practical, convenient, beautiful and marketable, taking into account the needs of different transportation and sales methods, conducive to recycling and reuse, and avoiding excessive packaging.
1
GB/T 3302-2009
4.1.2 The packaging design should meet the requirements of GB/T 19451 and GB/T 17306, and fully consider consumers’ environmental safety, economy, and applicable
sexual needs.
4.1.3 The main body of the package should be straight, and the main body and accessories should be complete, firm and consistent with each other.
4.1.4 The weight of each carton package should not exceed 40kg.
4.1.5 The packaging bar code should meet the requirements of GB/T 18127.
4.1.6 The color and pattern of the packaging should be beautiful, concise and reasonably matched.
4.1.7 The size of the bottom area of cuboid box packaging should meet the requirements of GB/T4892; the size of the packaged unit cargo should meet the requirements of
The requirements of GB/T 15233; the size of the packaging tray should meet the requirements of GB/T 2934.
4.2 Packaging materials
4.2.1 Packaging cartons should meet the requirements of GB/T6543, wooden boxes should meet the requirements of GB/T 12464, and pallets should meet the requirements of GB/T 12464.
The requirements of GB/T16470, other packaging materials should meet the requirements of GB/T9174.
4.2.2 Protective inner packaging materials should meet the requirements of GB/T 12339 and be kept dry and clean.
4.2.3 Metal sealing pins, straps and buckles should not be rusted, and the adhesive force of the sealing tape should be strong.
4.3 Packaging requirements
4.3.1 The packaging should meet the requirements of GB/T9174.
4.3.2 The packaging should ensure the safety of ceramic products, ensure that under normal storage and transportation conditions, the products and packaging are not damaged, and it is convenient for loading and unloading, storage and transportation.
export, trade, etc.
4.3.3 The packaging should be neat and well-formed, and there should be spacer materials for shockproof and anti-collision inside the box.
It is compact, firmly fixed, and the center of gravity is centered and lower.
4.3.4 The packaging of export products should meet the requirements of GB/T19142.
4.3.5 The product should be packaged only after passing the inspection.
4.3.6 The packaging operation should be carried out according to the design requirements. When packaging, the product type, quantity, design and color, and matching parts should be checked, and no mispacking should be allowed.
4.3.7 Corrugated boxes can be glued or stapled. When gluing into boxes, sealing tape should be used, the width of which should not be less than 5cm;
When sealing the box, the position of the needles should be reasonable, the gap between the cloth and the nails should not be greater than 7cm, the surface of the nails should be treated, and there should be no more than three floating needles in each box.
4.3.8 The sealing tape should be pressed accurately at the anastomotic opening of the sowing cover, and those with nails should be pressed at the same time, with both ends drooping, and there must be no obvious skew and separation.
4.3.9 The deflection of horizontal and vertical strapping shall not exceed 2cm, and the degree of tightness shall be close to the box surface without loosening, and the side of the box shall not be bitten or cracked. using heat
The bonded joint should be centered, and the joint length should not be less than 2.5cm; the buckle should be fastened tightly without sliding, and the tail length of the strap after the buckle should not exceed
5cm.
4.4 Packaging inspection
4.4.1 Packaging sampling adopts GB/T 2828.1-2003 normal inspection secondary sampling, its inspection level is general inspection level I, receiving quality
The Quantity Limit (AQL) is 6.5.
4.4.2 The appearance quality and marks of packaging materials and auxiliary materials shall be visually inspected.
4.4.3 For the inclination of the sealing strap, take the edge of the box as the baseline and measure the maximum deviation with a ruler.
4.4.4 The floating needle is judged by picking it up with fingers.
4.4.5 Stacking test and vertical impact drop test shall be carried out according to GB/T 4857.3 and GB/T 4857.5.
5 signs
5.1 The packaging marks should be correct, clear, complete and firm, meeting the requirements of GB/T191.
5.2 The sign should include the following contents:
a) The name, specification and quantity of the product;
b) Product quality standards, quality grades and inspection marks;
c) Signs of “Fragile Items” and “Afraid of Rain”;
d) Specifications, dimensions, gross weight, net weight, article number, and production batch number of the package:
2
GB/T 3302-2009
e) Manufacturer name, address, barcode:
f) Other signs that should be marked according to national regulations.
5.3 Signs may also include: telephone number, email address, website, trademark, third-party conformity mark authorized for use, etc.
5.4 The logo text shall use the standardized Chinese characters officially promulgated and implemented by the State Council. According to the specific requirements of the trade contract or the importing country (region), the exported products should use English or the official language of the country (region).
5.5 The unit of measurement of the mark shall be the national legal unit of measurement, and the quantity unit of the internal product shall be “piece”. 5.6 There should be no mistakes in the logo and text of the product.
5.7 Scribbled fonts, blurred printing, and serious color stains on the box surface are not allowed.
5.8 If it is not suitable to add a mark on the package due to its irregular shape or small size, it should be indicated in other appropriate ways, and the size should be based on the clearly identifiable graphics and text.
5.9 The transportation signs of international trade shall be carried out according to GB/T 18131. 5.10 Packaging recycling marks shall be implemented in accordance with GB 18455.
5.11 Those with special requirements shall be formulated by both trading parties. 6 Transport and storage
6.1 Transport and storage should adopt protective methods that are suitable for the characteristics of the product and packaging.
6.2 During transportation and storage, the package should avoid rain, snow, sun exposure, moisture and pollution. It shall not be stored or transported together with poisonous, harmful, corrosive articles and pollutants.
6.3 During transportation and storage, it should be handled with care, and transportation, loading and unloading methods and tools that damage the quality of the package should not be used. Packages should be packed tightly during shipment.
6.4 The product should be stored in a ventilated and dry warehouse. The storage ground should be hardened, flat, clean and away from fire sources.
6.5 During storage, the bottom layer should be no less than 15cm from the ground, and the stacking height should not exceed 180cm, and the lower layer of packages and products should not be crushed. 6.6 When storing in the open air for a short period of time, necessary measures such as protection against rain, snow and sun should be taken.
